亚洲人成av网站在线播放

    <pre id="iqcii"><ruby id="iqcii"></ruby></pre>

    <video id="iqcii"><optgroup id="iqcii"><th id="iqcii"></th></optgroup></video>

      1. <video id="iqcii"><kbd id="iqcii"><dfn id="iqcii"></dfn></kbd></video>
            Amazing Machinery, Your Equipment Superstore Since 1995
            Professional Jetter Business Package

            Sewer Jetter FAQ

            What is sewer jetting?

            Sewer Jetting is the application of directed high pressure water to remove clogs, dirt, grease, and/or grime from pipes to allow them to flow freely. A Pump, along with a jetter tip to create restriction, is used to generate a pressure in some cases powerful enough to cut through concrete. Sewer Jetting is a valuable means of cleaning interior pipe surfaces at incredible speeds.

            Which Sewer Jetter should I buy?

            We sell a wide variety of Sewer Jetters, accessories and parts. The easiest thing to do is call us toll free at 1-800-504-7435 and tell us your situation. We'll help you pick out the right model for your needs and budget.

            What’s more important, pressure (PSI) or water volume (GPM)?

            Both PSI and GPM are very important for the optimum performance from a sewer jetter. The pressure lifts the dirt and the water volume carries it away.

            What do I do with my machine in the winter?

            If you live in a climate where it is below freezing you will want to run pump saver antifreeze through your system before putting it to bed at night. When using auto antifreeze the mixture should be 50/50 antifreeze and water. The ideal condition is to store your machine in a climate controlled building but not all of us can do that.

            How do I run the antifreeze mixture into my machine?

            For a cart mounted machine try these simple steps. Using an old garden hose cut off the end with the male thread remaining in about a two to three foot section. Using a funnel insert it into the cut end and funnel pump saver antifreeze or a 50/50 mixture auto antifreeze/water through the pump by pulling the rope start several times until the mixture comes out the other end of the jetter hose. Be sure to drain water from all non-pressurized hoses on your machine to prevent freezing.

            For a truck or trailer mounted rig you may add a secondary tank with a capacity of 25-50 gallons, and have it plumbed to your supply line like your regular water tank with ball valves to control the flow. Allow the antifreeze mixture to flow through the high-pressure system and with your jetter tip back into the smaller tank it will recycle its self. You will have to change the antifreeze from time to time, as the mixture will become too diluted. Be sure to drain water from all non-pressurized hoses and tanks on your rig to prevent freezing.

            Should I remove the fuel from the tank when storing my sewer jetter?

            For safety reasons it's always best to remove the fuel for storage. If you do not plan on storing for longer than a month you can use a stabilizer. You should never store gas inside your home.

            How much sewer jetter hose can I use?

            Using 1/4" jetter hose, the recommended max length is 150' however you can run more. If you choose to use over 150' you may find the hose is not pulling as well into the pipe. On larger machines using 3/8" or 1/2" jetter hose, the recommend max length is 300'.

            What do the different Jetter nozzles do?

            Laser Nozzle or Penetrator Nozzle
            Cuts, Dislodges and Flushes blockages
            One Forward Jet, Three Backward Jets

            Ram Nozzle
            Rams and Flushes tougher debris
            Three Backward Jets

            Impactor Nozzle
            Moves sand, grit and light scale which may have accumulated within the line
            One Forward Jet, Three Sideward Jets, Six Backwards Jets

            Rotating Nozzle or Spin-Jet Nozzle
            Polishes and maximizes line recovery
            Two Side Facing Jets, 2 Backward Jets

            Flusher Nozzle
            Flushes loose debris
            Six Backward Jets

            De-Icer/De-Greaser Nozzle
            Removal of heavily blocked lines with grease, hard soap or even ice
            Three Forward Angle Jets, Six Backward Jets

            Cornering Nozzle
            Navigates around P-Traps and tight bends
            One Forward Jet, One Sideward Jet, Three Backwards Jets

            How do I clean a clogged nozzle?
            Remove the nozzle from your system Using our Nozzle Cleaner or a small piece of wire like a paper clip clear the clog. Flush water backwards through the nozzle and replace it on your sewer jetter. If it is still partially clogged, try again.

            How often should I replace my nozzles?

            This depends on much time you use your machine. A good rule of thumb is if you notice a gradual pressure lose you should replace that tip. Not all tips will wear out at the same time.

            Why should I keep my nozzles clean?

            A clogged nozzle will not clean as well and can increase the back pressure on your pump causing damage.

            What type of oil do I use in my pump?

            You want to use Non-detergent oil. You should always refer to your owner's manual to understand what type Non-detergent oil the manufacturer recommends.

            I have a hot water supply outside, can I run this through my pump?

            No, incoming hot water can damage your pumps seals. Our pumps have a max inlet Water temperature of 80 degrees with a max pump temperature of 140 degrees. If your pump exceeds 140 degrees the thermal relief valve will pop to protect your pump and it will need to be replaced. However you can add an optional Hot Pump Upgrade to most of our machines that will give you a max inlet water temperature of 140 degrees with a max pump temperature of 190 degrees to be used with hot inlet water.

            What does by-pass mean?

            This allows the pump to circulate water so there is no pressure build up however if you leave your machine in the by-pass mode for longer than two minutes you risk overheating your pumps. We use a thermal relief valve to stop this from happening.

            What is a thermal relief valve?

            This is a safety feature for your pump. It will keep the pump from burning up if left in the by-pass mode for too long. This valve is set to the max pump temperature rating. If the valve pops you will need to replace it.

            If you were not able to find the answer you were looking for in this section, call Amazing Machinery at 1-800-504-7435 to speak with one of our experienced Jetting Staff Members.

            ORDER TODAY! 1-800-504-7435
            Amazing Machinery Logo
            We accept credit cards and Paypal Lease This Jetter OAC

            Home | Contact Us | Site Index | LinksJetter FAQArticles | Testimonials | Terms of Use | Privacy

            Proposition 65: Information, required to show to our customers in California Follow us on Facebook Secure Website Amazing Machinery, LLC BBB Business Review


            Plumbing & Contractor's Equipment since 1995

            Sewer Cameras
            Viztrac
            Forbest
            Ridgid
            General Wire
            Opticam
            Electric Eel
            Wohler
            Locators - Line & Sonde

            Sewer Jetters
            BossJet Sewer Jetters
            Ridgid Sewer Jetters
            General Sewer Jetters
            Trailer Sewer Jetters
            Hot Water Jetters
            Jetter Conversion Kits
            Jetter Hoses
            Jetter Nozzles
            Nozzle Calculator

            Cable Machines & Cables
            Valor
            Ridgid
            Milwaukee
            Torque Master
            General Wire
            Steel Dragon
            Electric Eel
            Replacement Cables

            Plumbing Machinery
            Plumbing Parts & Accessories
            Business in a Box Packages
            Pump Out Systems
            Replacement Pumps
            Air Compressors
            Smoke & Smoke Blowers
            Job Boxes

            Drain Cleaning Specials
            Special Buy Jetters
            Business Packages
            Video & Locator Packages
            Viztrac Basic Sewer Cameras
            Jetter Conversion Kits
            BossJet Trailer Jetters

            Flat Surface Cleaners

            Clearance Specials
            Testimonials

            Blue Burst Specials
            Direct Drive Pump
            Jetter Nozzles
            Foot Actuated Valve
            Pulsation Valves
            Jetter Hose
            3000psi Ball Valve
            6 nozzle holder
            ZipDrain Jetter Attachment
            5 foot jumper hose
            Adjustable Unloader
            Pump Saver Antifreeze

            亚洲人成av网站在线播放

              <pre id="iqcii"><ruby id="iqcii"></ruby></pre>

              <video id="iqcii"><optgroup id="iqcii"><th id="iqcii"></th></optgroup></video>

                1. <video id="iqcii"><kbd id="iqcii"><dfn id="iqcii"></dfn></kbd></video>